Sublimation or Laser Engraving Mini Shot Glass Tumbler with lid and – ACC Sublimation Blanks & Designs

Mini "shot glass" tumbler is sublimation ready (all colors) and sized at approximately 2-3 oz. Includes lid and straw. (2oz capacity when lid is on, 3oz capacity without lid) Tumblers can also be engraved in a laser!   Convection oven requires the use of shrink wrap to apply pressure during baking, sold separately, and
Mini shot glass tumbler is sublimation ready (all colors) and sized at approximately 2-3 oz. Includes lid and straw. (2oz capacity when lid is on, 3oz capacity without lid) Tumblers can also be engraved in a laser!   Convection oven requires the use of shrink wrap to apply pressure during baking, sold separately, and accessories such as rubber bottoms and straw cleaning brushes are also available in a separate listing. ***Directions*** PLEASE NOTE: equipment varies and so may your required settings. Please test your own equipment using these baseline recommendations.  Apply sublimation transfer on the surface of the tumbler using heat tape. For full wrap designs, make sure you pull the transfer as tightly as possible around the tumbler, then tape very well along the seam and around the top/bottom of the tumbler. Pulling the tape/transfer as tight as possible with no air pockets. If your transfer does not fully cover the tumbler surface, apply blowout/butcher paper to the entire tumbler so that there is no metal showing on the sides.   *Convection Oven* (Equipment settings will vary!) Apply shrink wrap using a heat gun to shrink it tight to the tumbler. Bake in a convection oven at approximately 385-400 degrees F for 5-6 minutes, turning halfway. **If your tumbler is touching a metal surface during baking, the shrink wrap will be more likely to melt! Remove from oven and immediately remove shrink wrap and transfer. TUMBLER WILL BE HOT!! No sealant is necessary on sublimation tumblers. *Hand washing is recommended as the high heat in many dishwashers may reactivate the heat and cause it to bleed.  

Sublimation or Laser Engraving Mini Shot Glass Tumbler with lid and – ACC Sublimation Blanks & Designs

Shimmer White 20 oz Sublimation/Laser Engravable Insulated Tumbler - AVP Blanks

FECBK 3oz Mini Tumbler Shot Glass with Straw and Lid 12 Pcs Sublimation Shot Glasses Tumblers Blank Stainless Steel Cute Shot Glasses Set for Wedding Party Whiskey Cocktail Bar, 6

ACC Sublimation Blanks & Designs

Laser Cut Sublimation Blanks – ACC Sublimation Blanks & Designs

Mini shot glass tumbler is sublimation ready (all colors) and sized at approximately 2-3 oz. Includes lid and straw. (2oz capacity when lid is on,

Sublimation or Laser Engraving Mini Shot Glass Tumbler with lid and straw RTS

Equipment and Supplies – ACC Sublimation Blanks & Designs

Sublimation or Laser Engraving Mini Shot Glass Tumbler with lid and – ACC Sublimation Blanks & Designs

Sublimation or Laser Engraving Mini Shot Glass Tumbler with lid

Sublimation Mini 2oz Tumbler Shot Glass – Blanks and Bits

AGH 3 oz Sublimation Shot Glass Tumblers Set of 6 Colored Stainless Steel Small Tumblers Double Wall Vacuum Insulated Cups with Lids and Straws: Tumblers & Water Glasses

AGH 3 oz Sublimation Shot Glass Tumblers Set of 6 Colored Stainless Steel Small Tumblers Double Wall Vacuum Insulated Cups with Lids and Straws: Tumblers & Water Glasses

🥤 3 OZ MINI TUMBLER SHOT GLASS SET: Surprising 6 color tumbler shot glass(12 pieces)-[2 pcs green, 2 pcs orange, 2 pcs white, 2 pcs cyan-blue, 2 pcs

FECBK 3oz Mini Tumbler Shot Glass with Straw and Lid 12 Pcs Sublimation Shot Glasses Tumblers Blank Stainless Steel Cute Shot Glasses Set for Wedding