FP100 Fire Retardant Clear Coat - Int/Ext

FP100 Fire Retardant Clear Coat - interior/exterior over painted surfaces
FP100 is a high intumescent fire retardant coating. It can be used on any type of wood, porous or non-porous. Interior and exterior. Class A rated for ASTM E84, 30 minute extended test. ASTM E84 - Class A ASTM E2768 - 30 Minute Extended Test on engineered I-Joists and OSB High-intumescing action Dries clear Coverage rate - one coat at 200 sq ft per gallon. FP100 is a high intumescent retardant coating that swells as a result of heat exposure or flame, converting combustible gases and tars to non-combustible carbon char causing the surface to bubble-up and creating a thermal barrier between the fire and the treated material. The carbon char is a poor conductor of heat, protecting the substrate from being consumed by the fire. APPLICATION: Treat before, during or after construction. Be sure surface is clean and dry before treating. Apply with brush or roller. May be necessary to wipe on hardwood surfaces. Treat all surface areas where possible. Scuffing or lightly abrading the surface may be necessary to improve adhesion. Do not expose treated area to moisture for 24 hours. All surfaces to be treated must be clean and dry. FP100 fire retardant coating is a water-based, clear liquid that becomes insoluble when dry. On exterior wood FP100 can last five years or more, while maintaining a flame spread index of less than 25. In extreme weather conditions it may be necessary to re-coat surfaces every three to five years. It also acts as a preservative, waterproofing agent, ultra violet inhibitor, mold and mildew inhibitor, and it repels insects. If over coating is intended, FP100 fire retardant coating is an excellent surface primer for use under latex paints, or can be used as a finished coat over water based stains. Finished surfaces will exhibit semi-gloss to gloss finish similar to lacquers or epoxies. DO NOT DILUTE OR MIX FP100 FIRE RETARDANT COATING WITH ANY OTHER PRODUCTS. Contact parts of any equipment should be stainless steel or plastic to prevent chemical reaction and breakdown. Storage may be done in polyethylene containers. CAUTION: Product must not freeze. It must not be thinned or diluted. Do not apply FP100 below 40°F (4.45°C) or relative humidity conditions greater than 80%. OVERSPRAY: The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with bleach and water mix will clean up spotting.

CharCoat is an FM-Approved Intumescent Latex Cable Coating that stops fire from spreading on the cable surface at the source and simultaneously

CharCoat 90 Minute Retardant Paint for Wire & Cable

Fire Protection Coating, Epoxy Fire Coatings

Sustainability, Free Full-Text

Fire Coating Deals, SAVE 56%

Fire retardant coating for wood and wood products

FS2 Fire Retardant for Cedar Shake Shingles

Seismic Expansion Joint · SJS System · Sika Emseal

WT-103 is a clear, flat, matte, interior, fire-proof intumescent paint coating for raw wood. WT-103 works by creating a fire barricade, separating the

WT-103 5 gal. Clear Matte Latex Interior Intumescent Fireproofing Flame Retardant Coating for Wood

Fire Coating Deals, SAVE 56%

fire retardant coating for plywood, lumber, timber, OSB, I-joists

Fire Resistant Coating Delicate Colors

Fire Retardant for plastic, Flame Retardant Coating for styrofoam

Non-toxic and environmentally friendly. Free of bromides, halogens, organic compounds and other banned or toxic substances. Easy application, easy

FlameOFF- FR Clear interior fire retardant spray for Fabric, Curtains, Raw Wood. Non-toxic, Eco-Friendly, Water-Based. Tested to NFPA 701, ASTM E84/UL

Austin Fireproof, Austin Fire Retardant, Flame Retardant